top of page
Hands measuring across the chest of an unbranded rust-brown herringbone vintage-style jacket laid flat on a wooden table.

How to Compare Vintage Jacket Measurements Before You Buy

Writer: Rmar Vintage
Rmar Vintage
Nov 8
3 min read

Vintage jacket labels can be useful clues, but they are not a reliable substitute for measurements. Sizing systems, alterations and intended silhouettes vary, so the most practical comparison is often a jacket you already wear comfortably. The aim is not to force every garment into one modern size: it is to compare like with like and understand where the differences sit.


Hands measuring across the chest of an unbranded rust-brown herringbone vintage-style jacket laid flat on a wooden table.
Comparing the same measurement points on a jacket you already wear can make an online vintage-clothing description easier to assess.

Why jacket measurements matter


A listed chest, shoulder or sleeve measurement becomes meaningful only when you know how it was taken. Two sellers can describe the same point differently, while a tailored jacket, a soft unstructured blazer and an oversized coat may each need a different amount of ease. Comparing the seller’s method with your own reference garment helps you spot whether the numbers are genuinely comparable.


Measurements also reveal only part of the picture. Shoulder shape, armhole height, lining, padding and fabric behaviour can affect comfort even when the tape looks promising. Treat the numbers as evidence rather than a guarantee of fit.


Prepare a jacket you already know


Choose the closest comparison


Select a jacket with a similar intended use and silhouette. A formal tailored jacket is a better reference for another tailored piece than a loose raincoat. Fasten it only as you would normally wear it, empty the pockets and smooth it gently without pulling the cloth.


Lay it flat and keep the method consistent


Place the jacket on a clean, level surface with the front facing up. Arrange the shoulders and side seams naturally. Use a flexible tape and keep it straight, but do not press into padding or stretch the garment. Record where you started and finished so you can repeat the same method when checking a listing.


Measure the key points


Chest width


A common laid-flat chest measurement runs from one underarm point to the other. Check whether the listing gives a flat width or a full circumference, and never assume which one is meant. On your reference jacket, note the exact position of the underarm seam and whether the front overlaps or curves.


Shoulders, sleeves and back length


For shoulder width, compare the seam-to-seam line across the back when the construction has clear shoulder seams. Sleeve length may be measured from the shoulder seam or from the centre back of the neck, so read the method carefully. Back length is commonly taken from the base of the collar to the hem, but vents and dropped hems can complicate the figure.


Waist, hem and upper arm


These extra points can be valuable when a jacket is shaped, cropped or cut with narrow sleeves. Measure them only where the seller does, and avoid doubling a flat measurement unless the listing clearly uses circumference. If a dimension is important and missing, ask for it rather than estimating from photographs.


Allow for construction and movement


The difference between your body measurement and the garment measurement is ease. Enough ease is needed for movement and any layers worn underneath, but the preferred amount depends on the cut. Compare how your reference jacket feels when you reach forward, bend the elbows and sit down. Then use the measurements to judge whether the vintage jacket is likely to be roomier or closer in each area.


Do not rely on one number alone. A generous chest with a narrow upper arm may still feel restrictive; a broad shoulder with a short sleeve may need a different styling decision. Lining condition and previous alterations can matter as much as the outer measurements.


Read an online listing with a measurement checklist


Match each number to a method


Look for a clear description of where the tape began and ended. Photographs showing the tape in place are especially helpful. Check whether the garment was measured flat, fastened and unstretched, and compare every figure with the same point on your reference jacket.


Ask focused questions


When something is unclear, ask one specific question at a time: whether the chest figure is flat or doubled, where the sleeve was measured from, whether the jacket has shoulder padding, or whether the seams show signs of alteration. Precise questions are easier to answer accurately than a general request about fit.


Make the comparison before you decide


Write the seller’s measurements beside those of your reference jacket. Note the differences at the chest, shoulders, sleeves, length and any shaped areas. Then consider the cut, fabric, lining and how you plan to layer the garment. This simple comparison cannot promise fit, but it gives you a clearer basis for deciding whether to ask for more information.


Explore RMAR Vintage shop collections or visit RMAR on eBay for more pre-owned fashion.


Editorial note: the image illustrates a general measuring method and does not represent current RMAR Vintage stock.

Comments


bottom of page